lead-free

Avoiding Grief and Pain When Using Your Soldering Iron

In a recent blog post, we discussed soldering safety tips. Our team brings over 100 years of experience with soldering circuit boards. Over the years, we have learned the best practices on how to efficiently and safely solder a variety of electrical products, particularly printed circuit boards. Through our vast experience, we have also gained a clear grasp on what NOT to do while holding a Soldering Iron.

10 Things NOT to Do While Holding a Soldering Iron

Below is a helpful list that may spare you lots of grief and pain when using a Soldering Iron:

  1. EYE SPY PAIN
    Something in your eye? Please put the soldering iron down first. Thankfully your safety goggles are in place for absentminded events such as this. Singed eyelashes will be the least of your problems without your safety glasses securely fastened.
  2. NEW NOSE RING 
    Scratching an itchy nose with a soldering iron in your hand is typically not a good idea. Unless you are eager to add that new nose ring that you have been putting off. If that is the case, then the soldering iron will cut right through the victimized or targeted area. Viola! A new hole available for your new nose ring.
  3. OUCH!
    Absolutely under no circumstance should you zip up you fly if you notice it is down. No adjustments, fixing, or any other engagement in that general area while holding a soldering iron. Results could be disastrous. Plus you will have an extremely difficult time trying to explain this accident to the emergency room staff.
  4. USE Q-TIPS INSTEAD
    Feel water floating in your ears from the early morning swim? This is not the time to clean out your ears. Set down your soldering iron and grab a few Q-tips.
  5. NO KNEE-SLAPPERS
    Tell everyone around you no jokes if you are one to slap your knee when laughing. Yelling, “Hey Johnny, that’s a knee-slapper” can turn painful real quick once the soldering iron hits your knee.
  6. SEE #1
    Soldering is not a time to apply mascara or eyeliner. Please refer to rule #1.
  7. WORSE THAN A ROOT CANAL
    If you suddenly feel a piece of popcorn stuck in your teeth from that movie you watched three nights ago, please do not try removing the kernel while soldering. A soldering iron is not a replacement for a toothpick and this could quite easily be more painful than a root canal without Novocain.
  8. NO SELFIES
    Holding or using your cell phone while soldering typically falls under the category of a “Bad Idea”. If you find it necessary to Facetime or Go Live on Facebook while soldering, please have someone else hold the phone to film your activities. You will be glad you played it safe.
  9. HOLY SMOKES BATMAN
    Please under no circumstance do you want to apply lipstick or Chap Stick while holding a soldering iron.  You may end up looking like the Joker from Batman….permanently.
  10. NO STRETCHING 
    Last but not least, if you are sitting next to someone while soldering, please keep them beyond arm’s length. Especially if you like to speak with your hands, point when making a point, flail your arms when emotional, stretch frequently or tend to smack people on the shoulder when speaking. All of the above can cost you a friendship real quick.

Soldering Iron

We had fun putting together this list even though burns and injuries are a very serious matter. Please use extreme care and caution when using a soldering iron. Hopefully, these tongue-in-cheek comments convey the message. We use the safest measures possible when soldering printed circuit boards at our facility. Falconer Electronics has proudly participated in the SHARP program since 2005 to proactively maintain a healthy and safe workplace.

 

Thank you for taking the time to read our blog post. Continue looking for our series on soldering circuit boards.

Also, to learn more about wire harness assemblies, check out our weekly “Wire Harness Wednesday” blog posts.

Lastly, let’s get social! Please connect on FacebookTwitterGoogle+LinkedIn, and Pinterest for more electronic info.

 

0 replies

Leave a Reply

Want to join the discussion?
Feel free to contribute!

Leave a Reply